Skip to content
IDAHO
CATTLE GUARDS

Installation

How a cattle guard install actually goes

Site review, approvals if the road is public, excavate, base, set and level, wings and fence tie-in, gate where one is required, cleanout access. Base prep is most of the job: a guard set on disturbed ground settles, and a settled guard stops draining.

The four install steps, and the job from quote to installStep one, excavate the opening. Step two, build and compact the base. Step three, set the guard and check it level. Step four, fit wings and tie into the fence. Below, the job runs quote, site review, delivery, install.1EXCAVATE2BASE3SET + LEVEL4WINGS + FENCEQUOTESITE REVIEWDELIVERYINSTALL
Base prep is most of the job. A guard set on disturbed ground settles, and a settled guard stops draining.

The eight steps, in order

  1. Site review

    We look at the opening, the ground, the fence line and the approach. Width, load class, base type and whether wings are needed are all settled here rather than over the phone.

  2. Approvals, if the road is public

    On a public road, consent from the county or highway district comes before the dig - and on a state highway, an ITD encroachment permit. We help you through the steps; the decision is the authority’s.

  3. Excavate the opening

    The pit is dug to suit the product and the ground, with spoil placed where it will not block the lane. Rock, sand and a high water table all change this step, which is why it is priced after the site review.

  4. Build the base

    Compacted gravel, or poured concrete abutments where the load class or the ground calls for it. The frame has to bear on undisturbed or properly compacted material - this step is most of whether the crossing is still level in five years.

  5. Set the guard and check it level

    The guard is placed, seated and checked for level and bearing across its full length. A frame bearing on three points instead of its full seat is a frame that will move.

  6. Wings and fence tie-in

    Wings are fitted and your fence is brought to them and anchored, usually to a braced post rather than to the guard itself. The crossing is not finished while stock can walk around the end of it.

  7. Gate, where one is required

    On a public road the connected fence needs a gate at least 12 ft long within 33 ft of the highway, kept unlocked. We supply and hang it as part of the job.

  8. Cleanout access and handover

    We leave a way to get silt out of the pit, walk you through what to watch for, and photograph the finished crossing.

What an install quote includes

Always
Site review, excavation, base, setting the guard, wings, fence tie-in, cleanout access.
Where required
The gate on a public-road crossing, supplied and hung.
Priced separately
Delivery beyond the service area, a ranch gate add-on, approval paperwork time.
Never included
A promise about an approval. We help you through the steps; the authority decides.
Gravel base compared with concrete abutmentsTwo sections side by side. On the left, a boxed guard set on compacted gravel with a shallower excavation. On the right, a guard set on poured concrete abutments with a deeper excavation and more room for cleanout.Gravel baseCOMPACTED GRAVELSHALLOWER DIGConcrete abutmentsPOURED ABUTMENTSDEEPER DIGSCHEMATIC - DEPTHS PER SITE AND SPEC
Which base you need depends on the ground and the load class, and it is settled at the site review - not from a catalogue.

Gravel or concrete

Compacted gravel is the common base on private ranch roads: less excavation, no cure time, and entirely adequate where the ground is good and the load class is modest. Poured abutments come in when the load class is higher, when the ground will not compact to something dependable, or when the road authority expects them.

Rock makes excavation slower and more expensive. Sand makes compaction harder. A high water table changes both and can decide the base for you. None of that is visible from a catalogue, which is why the base is quoted after someone has stood in the opening.

Wings, fence and the statutory gate

Wings and the fence tie-in are part of the install, not extras: a crossing stock can walk around is not a crossing. And on a public road, Idaho Code 40-2310 requires a gate at least 12 ft long in the connected fence, no more than 33 ft from the highway, kept unlocked at all times.

The rules, with the citation

Plan view: cattle guard, wings, fence tie-in and gateLooking down on a crossing. The guard sits in the road opening, wings flare out to meet the fence on each side, and a gate at least twelve feet long sits in the fence line within thirty-three feet of the highway.WINGSGUARD IN THE OPENINGGATE, 12 FT MINIMUMFENCE TIE-INROAD
On a public road, Idaho Code 40-2310 requires a gate at least 12 ft long in the connected fence, within 33 ft of the highway, kept unlocked.
Cleanout: a clear pit against a silted oneTwo sections. On the left, a clear pit under the rails with visible depth and drainage. On the right, the same guard with the pit filled with silt, so the rails sit on fill and stock can see a solid surface.ClearVISIBLE DEPTHDRAINS AND DRIESSilted upNO DEPTH TO SEEHOLDS WATER, LIFTS IN FROSTCLEANOUT ACCESS IS PART OF THE INSTALL, NOT AN EXTRA
A cattle guard works because stock can see depth. Once the pit fills, it is a bridge - which is why the install leaves a way to get the silt out.

Cleanout is the maintenance

A cattle guard deters livestock because an animal sees depth under the rails. Once the pit fills with silt, hay and gravel, that depth goes and so does the deterrent - and the pit starts holding water instead of draining it. So the install leaves a practical way to get the material out, and we show you where it is before we leave.

Questions we get asked

How long does a cattle guard installation take?
A straightforward gravel-base install is normally a one-day job once the guard is on site. Concrete abutments add cure time, which makes it a two-visit job. Rock, a high water table or an access problem can extend any of it - which is what the site review is for.
What do you need from me before the install?
Access for a truck and a machine, agreement on exactly where the crossing goes, and any approval the road authority requires. If the crossing is on a shared or easement road, the other users should know before we arrive.
Can I install it myself?
Yes, and plenty of people do - we will sell you the guard on its own and deliver it inside our service area. We do recommend professional installation for anything rated for road use, because a load rating assumes a bearing condition you have to actually build.
Who does the work?
We supply the guard and line up a local crew to set it. We are not a construction company and we do not employ the crew - what we do is make the whole job one conversation: the right product, delivered, with a crew booked for a day that works. The alternative is ordering steel from one company and then ringing round for an excavator yourself.
What about cleanout afterwards?
Plan on checking the pit each season and clearing it before it fills. A silted guard stops deterring stock and starts holding water, and water in a pit through an Idaho winter is how frost lifts a frame.
Do you remove the old gate?
Usually we keep it. On a public-road crossing the statute requires a gate in the connected fence anyway, so an existing gate in good condition often moves rather than leaves.

Send photos of the opening

Two photos from 20 ft back and a rough width get us a long way before anyone drives out. You can attach them to the quote form.

Get my free quote