Skip to content
IDAHO
CATTLE GUARDS

Specifications

How to read a cattle guard spec sheet

Six figures tell you what a cattle guard is: clear span, overall width, rail size and profile, rail spacing, weight, and the load rating with the standard it is stated against. A seller who will not give you all six - with the document behind them - is asking you to take the most consequential part on trust.

The figures that matter

SpecWhat it governsAsk for
Clear spanThe unsupported distance the structure carriesThe figure, and what it bears on at each end
Overall widthWhether equipment stays on the railsWidth with and without wings
Rail size and profileStrength, and how it drivesDimensions and whether flat bar or pipe
Rail spacingWhether livestock respect itCentre-to-centre spacing, as designed
WeightHow it gets off the trailerWeight per unit, as shipped
Load ratingWhat may legally and safely crossThe rating, the standard, and the document
FinishService life in a wet pitGalvanised or painted, and the coating spec
Cattle guard cross-sectionSide section through a cattle guard: rails spanning two concrete abutments over an excavated pit, with a gravel cleanout below and the roadway on each side.OPENING WIDTHRAILS + SPACINGABUTMENTGRAVEL CLEANOUT
Cross-section of a concrete-abutment install. Schematic: rail size and spacing come from the manufacturer's spec sheet.

A spec describes a structure, not an object

The frame, what it bears on, and the pit under it are one system. A rating is a statement about that system under stated assumptions - so "this guard is rated for X" is only true while the assumptions hold. Changing the span on site, or seating the frame on fill, changes the structure the rating describes.

That is why we ask what the rating assumes, and why the base is quoted after someone has looked at the ground.Load classes.

Flat bar or pipe

Flat bar presents a flat running surface: easier on tyres, feels solid, holds mud longer. Pipe sheds mud and snow and is less sure underfoot. Both are normal and neither is the "professional" choice - what the spec sheet should tell you is the size, the wall thickness where it applies, and the spacing.

Flat rail compared with pipe railEnd-on section of two cattle guards. On the left, flat bar rails presenting a flat top surface. On the right, round pipe rails presenting a curved top surface.Flat railFLAT RUNNING SURFACEEASIER ON TYRESHOLDS MUD LONGERPipe railROUNDED SURFACESHEDS MUD AND SNOWLESS SURE UNDERFOOTSCHEMATIC - RAIL SIZE AND SPACING PER MANUFACTURER SPEC
Rail size and spacing are the manufacturer's figures, and spacing is what decides whether stock respects the guard. Neither type is "better" - they trade differently in mud and snow.
Cleanout: a clear pit against a silted oneTwo sections. On the left, a clear pit under the rails with visible depth and drainage. On the right, the same guard with the pit filled with silt, so the rails sit on fill and stock can see a solid surface.ClearVISIBLE DEPTHDRAINS AND DRIESSilted upNO DEPTH TO SEEHOLDS WATER, LIFTS IN FROSTCLEANOUT ACCESS IS PART OF THE INSTALL, NOT AN EXTRA
A cattle guard works because stock can see depth. Once the pit fills, it is a bridge - which is why the install leaves a way to get the silt out.

The specification nobody prints

No spec sheet states how often the pit needs clearing, because that depends on your road and your water. But it is the figure that decides whether the crossing still works in five years. Plan on checking it each season, and keep the access the install left you.

What we currently publish

No published specs yet. We publish a spec once we hold the manufacturer document that states it. Ask us for the spec sheet for any product and we will send it as it was given to us.

Questions for any seller

Rating
What is it rated to, and against which standard?
Document
Can I see the sheet or certificate for this exact product?
Bearing
What base condition does the rating assume?
Spacing
What is the designed rail spacing?
Weight
What does it weigh, and what do I need to unload it?

Questions we get asked

What should a cattle guard spec sheet tell me?
Clear span and overall width, rail size and profile, rail spacing, frame construction, weight, the load rating with the standard it is stated against, and the bearing or base condition the rating assumes. If any of those is missing, ask for it before you buy.
Why does rail spacing matter so much?
Spacing is what the animal experiences. Too close and a guard loses its deterrent; too wide and you are into hoof-injury territory and a rougher crossing for vehicles. It is a manufacturer figure, set by design, and not something to adjust on site.
How heavy is a cattle guard?
Heavy enough that the answer changes how you receive it - a 16 ft steel guard runs well over half a ton, and precast concrete units are heavier again. We ask what you have on site to unload before we send a truck. The exact weight comes from the product spec.
What does galvanised buy me?
Corrosion protection, and therefore life, particularly where a pit holds moisture. Painted steel is cheaper up front. Which makes sense depends on how wet the crossing is and how long you intend it to be there.
Do you publish your own specifications?
No, and that is deliberate. We are not a manufacturer, so we have no specifications of our own to publish. Every figure we show comes from the manufacturer document that states it, and a quote carries that document rather than our retyping of it.
Get my free quote